LED SMD Indicator JET with sequential Blink technology
€93.95
Available, delivery time: 1-3 days
LED SMD Indicator JET with sequential Blink technology
Very noble and high-quality LED running light indicator with housing made of black anodised aluminium.
Powerful and ultra-bright sequential SMD LED technology.
Manufactured to a very high standard - 100% dust and waterproof - no problems with moisture!
Modern look in dark tinted clear glass design. Cover glass dark tinted, LEDs glowing orange.
The dimensions of the indicator head are just 48x18 mm! Very small, but due to the very conspicuous sequential flashing technology still much more visible than many larger turn signals.
The turn signals are E-approved for front and rear.
Price per pair.
- Turn signals with E-mark for front and rear
- Stylish, sturdy aluminium housing, black anodised
- dark tinted glass
- 12V / 4 W
- rubber-mounted M8 treat
- new sequential flashing technology
- cable length 40 cm
- total length: 92.2 mm
- dimensions: depth 15.8 x height 18.2 mm
- thread: M8
- Price per pair
Depending on the motorbike model, either a pair of resistors or an electronically controlled, load-independent flasher relay is additionally required!
See accessories.
OFF-THE-ROAD - OTR-Performance GmbH
Hugo-Junkers-Str. 52-54
50739 Köln, Deutschland
info@off-the-road.de
ZUBEHÖR
Available, delivery time: 1-3 days
Model specific indicator adapter acble for Yamaha Tenere 700. This adapter cable is needed to connect aftermarket indicator with 3.5mm round plugs to the Yamaha system connectors. So no extra welding or crimping of connectors necessary. Price per Pair Fits all: Yamaha Tenere 700 up to 2022 (without factory LED indicators) Yamaha Tenere 700 Rally up to 2022 (without factory LED indicators) Does not fit 2023 onwards models with OEM mounted LED indicator!
Available, delivery time: 1-3 days
Indicator adapter brackets (Indy Spacers) Aluminium for Yamaha Tenere 700 High-quality, strong and for "off-road" use made indicator plates. Made of black anodized aluminum. The visible outer spacers are CNC milled, the inner ones are precisely laser cutted. With the adapter set, most aftermarket LED flashers can be mounted quickly and easily on the Tenere 700. Suitable for the front or rear indicator mounts. Fits 8 mm and 10 mm indicator threats. Sold as a set for one pair of indicators. Suitable for all: Yamaha Tenere 700 2025 onwards Yamaha Tenere 700 Rally 2025 onwards Yamaha Tenere 700 2023 - 2024 Yamaha Tenere 700 Rally Edition 2023 - 2024 Yamaha Tenere 700 World Raid 2022 - 2024 Yamaha Tenere 700 World Rally 2023 - 2024 Yamaha Tenere 700 Explore 2023 - 2024 Yamaha Tenere 700 Extreme 2023 - 2024
Available, delivery time: 1-3 days
Small, but very usefull rubber cover for flasher ends with M8 threat. If turn signals are bolt to e.g. a license plate holder, the thread and nut of the turn signal is often visible. The rubber cover not only eliminates this optical flaw, it also prevents from too much dirt on the thread. Suitable for all turn signals with M8 thread. Price per set with 4 pieces.
Available, delivery time: 1-3 days
Why are installing load resistors necessary for LED turn signal lights? Resistors for LED indicator, which have a much lower power consumtion compared to standart 21w indicators. If you don't install load resistors (also known as equalizers) with LED turn signal bulbs, you will experience the notorious hyper flash issue. Hyper flash is exactly what it sounds like, where the turn signal light flashes rapidly and is almost headache inducing. Not only is this ugly, but you may also attract the police who think your bulb is burned out. Just connect the resistors between the indicators and the wiring harness. Delivered as a set for 2 indicators. For the Yamaha XT-660 models as an alternative also an electronic flasher relais can be used. Resistors avaiable in two load values: · 27 Ohms / 5 Watt · 6.8 Ohms / 25 Watt (for bikes with warning flashers like e.g. XT-660, XT-1200Z)
Available, delivery time: 1-3 days
Frequency stabilised flasher relay for LED indicators with load range from 0.1-100 watts Especially when you have problems with the dash board lights this relay is be the solution. Water and shock resistant, for use with combination of standart 21w and LED indicators or only with LED indicators. Works also on bikes with hazard indicators! You only need 1 relais for 1 bike - doesn't matter is you have 2 or 4 new indicators. Additional ground connetion wire. Fits e g.: Yamaha Tenere 700 up to 2022 (without factory LED indicators) Yamaha Tenere 700 Rally up to 2022 (without factory LED indicators) Yamaha XT-660R/X Yamaha XT660Z Yamaha XT-660ZA Tenere ABS Yamaha XT-1200Z Yamaha XT-1200ZE Yamaha MT-03 Yamaha MT-07 .....
Available, delivery time: 1-3 days
Frequency stabilised flasher relay for LED indicators with a switching capacity of 0.1-100 watts. Water and shock resistant, for use with combination of standart 21w and LED indicators or only with LED indicators. Works also on bikes with hazard indicators! You only need 1 relay for 1 bike - doesn't matter is you have 2 or 4 new indicators. Please note: This relay has a switching capacity of 0,1-100 watts. In newer vehicles, the power consumption of 4 turn signals can be much less than 1 watt. Especially if an LED for the turn signal indicator is used in the dash board as well, the cockpit LED might not "flash". In this case, the LED for the turn signal indicator does not work correctly. Please install a resistor on one of the right or left hand indicators. Also the relay with part number EL-BLR-4P provides a reliable remedy. No additional resistors needed. EL-BLR-4P is our recommendation to use e.g. with Yamaha Tenere 700 (up to year 2022). Newer models does not have indicator relais anymore) Fits e g.: Yamaha XT-660R/X Yamaha XT660Z Yamaha XT-660ZA Tenere ABS Yamaha XT-1200Z Yamaha XT-1200ZE Yamaha MT-03 Yamaha MT-07 Yamaha Tenere 700 up to 2022 (without factory LED indicators) Yamaha Tenere 700 Rall up to 2022 (without factory LED indicators) etc...