OTR LED tail tidy kit Yamaha

Small, but very usefull rubber cover for flasher ends with M8 threat. If turn signals are bolt to e.g. a license plate holder, the thread and nut of the turn signal is often visible. The rubber cover not only eliminates this optical flaw, it also prevents from too much dirt on the thread. Suitable for all turn signals with M8 thread. Price per set with 4 pieces.

LED indicator Slight with newest SMD Technology New look with glas in front and rear direction. Flashing to the front direction very bright, to the rear darker. LED in orange colour. The measurements of this indicator are only approx. 45 x 10 mm! Extremely small but very bright! The overall length of the indicator (without threat) is about only 60 mm. E-marked for front and rear use. Newest SMD LED technology for your safety. Avaiable in black or stylish blue, red or white! Depending on the model you might need a pair of resistors or an LED flasher relais! See accessories. · newest SMD Technology · Meassurments: 45x10mm · Length about 60mm · street legal · avaible in different colours · Price per pair

The current highlight amongst the LED indicators now avaiable. Strong 'SPEAR' look with tinted glas. Latest LED technology with very bright orange light for a safety plus. Small but very bright light. E-marked for front and rear use. Sold as a pair for front or rear use. · Material: plastic, black, glas tinted · perfect look for your bike · 2 indicators per set · Dimension approx.: L: 51 x W: 25 x H: 23mm · needed flasher relais or resistors to be ordered seperately · easy to fit

The latest LED indicator highlight! Angular stealth look in clear glass design. Clear cover glass, LEDs illuminated in orange, indicator tip with a stylish orange design. The dimensions of the turn signal head are just 45 x 25 mm! Very small and super bright. A 1-euro piece for comparison in the picture.   The total length of the indicator, without thread, is approx. only 60 mm. The turn signals are E-approved for front and rear.   current, bright LED technology for added safety plastic, black, glass smoked grey optically perfectly matching turn signals approx. dimensions: L: 45 x D: 25 x H: 15mm price per pair   Depending on the motorbike model, either a pair of resistors or a new, electronically controlled, load-independent flasher relay is additionally required! See accessories.

The LED indicator Stealth is now avaible in the even smaller Stealth II version! Sharp 'Stealth' look with clear lens design. Cover glass clear, LED glow in orange. Measures of the indicator head only approx. 29x18mm! Extremly small but very bright light. The indicators are E-appoved, for use the front and rear. Sold as a per pair.

High-quality sequnetial LED indicator in a black anodised aluminium housing. Ultrabright SMD LEDs! Ultra powerful SMDs with new sequential Blink technology enable the indicator in a very small housing. Very precisely made - 100% dust and waterproof. No problems with humidity! Modern look with clear glass and orange LEDs. The measurements of the indicator head are only 51x13 mm! Extremely small but brighter than a lot of other, much bigger indicators. E-marked for front and rear use. Price for a pair. · Turn signal E-marked for front and rear · Aluminum housing black · slightly tinted glass · 12V / 3.2W · rubber mounted · New sequential Blink technology · Cable length 18cm · Overall length: 88 mm · Dimensions: L 51 x Ø 13mm · Connection: M8 Pair · Price per Pair Depending on the bike you might need a pair of resistors or a new electric LED flasher relais. See accessories  

High-quality SMD LED indicator in a black aluminium housing.   Ultrabright SMD LEDs! 5 powerful SMDs make sure you have an unbeatable bright flash light. Very precisely made - 100% dust and waterproof. No problems with humidity! Future design with smoke grey glass and orange LEDs. The measurements of the indicator head are only 35x12 mm! Extremely small but brighter than a lot of other, much bigger indicators. Also avaiable as an indicator/tail/brake light combination E-marked for front and rear use. Price for a pair.   Measurements:   Length 44 mm x Height 13 mm  x Deepth 15,5 mm (including lens) Rubber arm: D. 13 mm, L. 11 mm Bolt M8 x 1.25 mm, Length ~ 20 mm   Depending on the bike you might need a pair of resistors or a new electric LED flasher relais. See accessories

High-quality LED indicator or indicator/tail/brake light combination in a black aluminium housing. Ultrabright SMD LEDs! 3 ultra powerful SMDs enable the indicator in a very small housing. Very precisely made - 100% dust and waterproof. No problems with humidity! Future design with clear glass and orange LEDs. The measurements of the indicator head are only 32x12 mm! Extremely small but brighter than a lot of other, much bigger indicators. Avaiable as indicator or indicator/tail/brake light combination E-marked for front and rear use. Price for a pair. Measurements: A: 32 mm B: 45 mm C: 11 mm Bolt threat M8 x 1.25 mm, Length ~20 mm. Depending on the bike you might need a pair of resistors or a new electric LED flasher relais. See accessories  

Frequency stabilised flasher relay for LED indicators with a switching capacity of 0.1-100 watts.   Water and shock resistant, for use with combination of standart 21w and LED indicators or only with LED indicators. Works also on bikes with hazard indicators! You only need 1 relay for 1 bike - doesn't matter is you have 2 or 4 new indicators.   Please note: This relay has a switching capacity of 0,1-100 watts. In newer vehicles, the power consumption of 4 turn signals can be much less than 1 watt. Especially if an LED for the turn signal indicator is used in the dash board as well, the cockpit LED might not "flash". In this case, the LED for the turn signal indicator does not work correctly. Please install a resistor on one of the right or left hand indicators. Also the relay with part number EL-BLR-4P provides a reliable remedy. No additional resistors needed. EL-BLR-4P is our recommendation to use e.g. with Yamaha Tenere 700 (up to year 2022). Newer models does not have indicator relais anymore)   Fits e g.:   Yamaha XT-660R/X Yamaha XT660Z Yamaha XT-660ZA Tenere ABS Yamaha XT-1200Z Yamaha XT-1200ZE Yamaha MT-03 Yamaha MT-07 Yamaha Tenere 700 up to 2022 (without factory LED indicators) Yamaha Tenere 700 Rall up to 2022 (without  factory LED indicators) etc...

Why are installing load resistors necessary for LED turn signal lights? Resistors for LED indicator, which have a much lower power consumtion compared to standart 21w indicators. If you don't install load resistors (also known as equalizers) with LED turn signal bulbs, you will experience the notorious hyper flash issue. Hyper flash is exactly what it sounds like, where the turn signal light flashes rapidly and is almost headache inducing. Not only is this ugly, but you may also attract the police who think your bulb is burned out. Just connect the resistors between the indicators and the wiring harness. Delivered as a set for 2 indicators. For the Yamaha XT-660 models as an alternative also an electronic flasher relais can be used. Resistors avaiable in two load values: · 27 Ohms / 5 Watt · 6.8 Ohms / 25 Watt (for bikes with warning flashers like e.g. XT-660, XT-1200Z)  

OTR license plate holder, inclination adjustable Made from laser cutted and cnc-bend aluminium. Black anodised for long lasting superp finish. To be used e.g. with our XT-660 tail light modification kit. Also very good for individual use on different bikes. Fits most license plates. · Universal, adjustablenumber plate holder ·  laser-cut 3mm aluminium · black anodised · available in two versions · Adjustable version: inclination angle adjustable (moveable) and adjustable indicator mounts · stainless steel mounting bracket · Mounting with 4 x M6 bolt · Width (number plate area): 180mm  

Universal number plate reflector mounting bracket. Can be used e.g. with our number plate holders. Length of the longer side up to the bend is 12.5 cm. Delivered without reflector.  

Universal number plate reflector. To be used with our reflector mounting bracket. Can be used e.g. with our number plate holders. Can be srewed (M5) or glued (self sticking backside) Size: 120x12 mm Delivered without reflector bracket! See accessories.  

Aluminium license plate holder, non adjustable   Aluminiumnumber plate holder made from laser cutted and cnc-bend aluminium. Black anodised for long lasting superp finish. To be used e.g. with our XT-660 tail light modification kit. Also perfect for individual made number plate holder on various bikes.   Details:   fits most license plates. universal laser-cut aluminium number plate holder black anodised standard version: inclination angle not adjustable (standard) bold on with 4 x M6 bolts width (number plate area): 180 mm   Fits:   universal