Lowering kit 30 mm Yamaha Tenere 700 World Raid 2026 onwards

Quality front or rear wheel bearing set Yamaha Tenere 700   Avaiable as complete bearing sets for the front or rear wheel as well as a set for both axles. Due to non sealing of the oem wheel bearings, this parts will be worn quite early. We offer high quality, double sealed (2RS) bearing set from european manufactors.   for seals check accessories tab.   Tip: always use some suitable grease between the radial shaft seals and the bearing!   Fits for all: Yamaha Tenere 700 2019 - 2024 Yamaha Tenere 700 Rally Edition 2020 - 2024 Yamaha Tenere 700 World Raid 2022 onwards Yamaha Tenere 700 World Rally 2023 - 2024 Yamaha Tenere 700 Extreme 2023 - 2024 Yamaha Tenere 700 Explore 2023 - 2024 Yamaha Tenere 700 2025 onwards Yamaha Tenere 700 Rally 2025 onwards

Rear shock lower linkage bearing and seal kit Yamaha Tenere 700 Often this bearing is mounted with not enough grease during the assembly at Yamaha - this causes a high weraring of this bearing. Check regulary! Contains a high quality needle bearing, a polished bushing and two oem quality seals. Fits all: Yamaha Yamaha Tenere 700 2025 onwards Yamaha Yamaha Tenere 700 Rally 2025 onwards Yamaha Yamaha Tenere 700 2019 - 2024 Yamaha Yamaha Tenere 700 Rally Edition 2020 - 2024 Yamaha Tenere 700 World Raid 2022 onwards Yamaha Tenere 700 Extreme 2023 onwards Yamaha Tenere 700 Explore 2023 onwards

This fork spring kit is made to lower the front height of the Yamaha Tenere for about 35mm. In combination with fitting lowering bones, the height of the Yamaha Tenere will also be good for smaller riders. Seat height will go down for about 35-40mm, depending on the lowering kit. The included progressive lowering fork springs can be used to lower the frontend of the motorcycle when it is not possible to lower the forks through the yokes (triple clamps). Perfect for smaller riders. Also a security feature if your feeto do not touch the ground perfectly. With these springs you get the bike lowered without having negative effects on the suspension. Hyperpro advises to lower both front and rear of the motorcycle to be assured of the best result. Rear can be lowered by lowering links or a custom made shock. See accessories. HYPERPRO lowering fork springs distinguish themselves by their continuous increase of the spring rate (Link-System Curve) in the whole range. They have been especially developed and tested for the Tenere 700. The manufacturing process has been made perfect: First-class, high-alloyed chrome-silicon-steel is used exclusivley. It is nearly tolerance freely coiled on computer-operated machines. The manufacturing is carried out according to DIN 2095. At the end, the outside of the springs is polished in order to achieve a minimal friction value. Of course, the forkspring sets are delivered with a ABE Certificate. The fork springs are delivered with 2 liter fork oil! Why progressive springs? · Using a linear, "normal" standard spring, all turns of the spring get loaded with the same weight at the same time. Imagine a spring with 10 turns at intervals of 1 cm - if you push the spring down 1 cm it shortens 1 cm, thus, the intervals between the single turns shorten to 0.9 cm. Using a two-step spring, half of the coils have a shorter interval. When the spring is compressed, the intervals shorten. At a certain point, the coils of the closer turns contact. · The spring "blocs" and stiffens. Now, only the turns with a greater interval keep working. The suspension comfort and the vehicle response drop rapidly. · Unfortunately, one needs more than 2 steps for driving because the powers occur progressively. That means, hardly any powers are needed to let the spring deflect. Though, the higher the power which affect the carriage, the more antagonising power of the spring. The result is a n essentially improved drivability, an improved braking action (because the front does not descend as much), an increased stability - and thus, an overall improved driving safety. Scope of delivery: · Fork Springs fpor lowering · Mounting instructions · 2 liters fitting fork oil · Mounting and Set-up instructions Fits all: · Yamaha Tenere 700 2019 - 2024 · Yamaha Tenere 700 Rally Edition 2020 - 2024

Complete suspension link arm (pivot) bearing repair kit including bearing pins for Yamaha Tenere 700. Comes with all needed parts to exchange the complete link arm bearings and seals. The set contains 4 bearings and seals for the swing arm linkage, 2 bearing and seals for the bottom of swingarm and 1 bearing and 2 seals for the shock linkage. Also included are the hardened shafts for the swing arm linkage, the bottom of the swingarm and the shock.   The set contains: 7 x high quality needle roller bearings (4 x linkage, 2 x lower side swingarm, 1 x lower shock linkage) 8 x oil seals (NBR quality) 4 x grounded and hardened shafts   Fits all: Yamaha Yamaha Tenere 700 2025 onwards Yamaha Yamaha Tenere 700 Rally 2025 onwards Yamaha Yamaha Tenere 700 2019 - 2024 Yamaha Yamaha Tenere 700 Rally Edition 2020 - 2024 Yamaha Tenere 700 World Raid 2022 onwards Yamaha Tenere 700 Extreme 2023 onwards Yamaha Tenere 700 Explore 2023 onwards

Complete suspension link arm (pivot) bearing repair kit for Yamaha Tenere 700 model range. Comes with all needed parts to exchange the complete link arm bearings and seals. Contains 4 bearings and 4 seals for the swing arm linkage and 2 bearing and 2 seals for the bottom of swingarm. Lower rear shock linkage bearing / seal kit not included. See accessories.   The set contains: 6 x high quality needle roller bearings 6 x oil seals (NBR quality)   Fits for all: Yamaha Yamaha Tenere 700 2025 onwards Yamaha Yamaha Tenere 700 Rally 2025 onwards Yamaha Yamaha Tenere 700 2019 - 2024 Yamaha Yamaha Tenere 700 Rally Edition 2020 - 2024 Yamaha Tenere 700 World Raid 2022 onwards Yamaha Tenere 700 Extreme 2023 onwards Yamaha Tenere 700 Explore 2023 onwards