Precisely machined billet clutch and brake lever for the Yamaha XT660Z Tenere Our Clutch and Brake Lever are CNC Machined of 6061-T6 billet aluminum to precise tolerances. Both clutch and brake levers are fully adjustable and we offer them in s stiff(straight) or foldable version. Our levers even come in a variety of colors to match your Tenere. Just remove your old levers, and re-insert the new one. Simple, but change the look of your bike totally. The levers have a small inset 1-1/4 inches from the end of the lever to provide a break-away point in a garage tip-over or otherwise. Adjustable in 6 positions. Made from billet aluminium. The levers are avaiable in black, blue, red and silver. The small adjuster tips are avaiable in blue, red, black and silver. This lever version is about 2.5cm shorter than oem levers. So e.g. mounting of handguards will be much easier and levers do not break that easy. With the almost infinite number of different colour combinations, you can put together your own desired levers and make your Tenere unmistakable. Due to the many different variants, the lever sets are always assembled individually and made to order only after an order has been placed - so please allow for a short delivery time. · CNC-machined levers · high grade air craft aluminium · Pre-defined breakage-notch for additional safety · Adjustable in 6 positions and in a foldable or standard version · available in different colors · foldable or non-foldable version · Choose lever type and color in the menue · Steet legal with TUV certificate Fits all: · Yamaha XT-660Z Tenere 2008-20016 · Yamaha XT-660ZA (ABS) Tenere 2011-2016

Precisely machined billet foldable clutch and brake lever set Yamaha XT-660Z Tenere 2008-2016 Our Clutch and Brake Lever are CNC Machined of 6061-T6 billet aluminum to precise tolerances. Each lever made from 7 cnc machined parts. The Clutch and brake levers are fully adjustable in width and length and come in a foldable version to avoid a damage when falling down. The levers even come in a variety of colors to match your Tenere. Just remove your old levers, and re-insert the new one. Simple item, but it changes the look of your bike totally. The levers have a small inset 1-1/4 inches from the end of the lever to provide a break-away point in a garage tip-over or otherwise. Position of the lever adjustable in 6 positions, length adjustable. Comes as a foldable lever. With the almost infinite number of different colour combinations, you can configure your own desired levers and make your Tenere truly unique. Due to the many different variants, the lever sets are always assembled individually after ordering - so please allow 2-3 days till shipping.   · Adjustable in 6 positions · Length adjustable · Foldable · Made from billet aluminium · CNC-machine high grade air craft aluminium · Pre-defined breakage-notch for additional safety · Available in different colours Fits all: · Yamaha XT-660Z Tenere 2008-2016 · Yamaha XT-660ZA ABS Tenere 2011-2016

Made from high quality plastic, thisTouring screen for the Yamaha XT-660Z Tenere offers greater protection from wind and rain than the stock OEM wind screen. Turbulence around the helmet is minimised which results in a more enjoyable riding experience, even on longer distance rides. The fly screen is about 8cm higher than the stock screen. Width is about the same like the stock screen. Street legel, TUV approved!   The screen was recommended in the big 'Motorradfahrer' magazin accessories test in April/2010!   Details: Touring Adventure screen for the Yamaha XT-660Z/ZA Tenere 2008 onwards Better windprotection for a more comfortable ride Made of high grade break-proof Makrolon Easy to mount, no changes necessary About 8cm higher than the stock screen - width same as stock Avaiable in different tints Recommended by 'Motorradfahrer' magazine TÜV approved Very good wind and weather protection   Fits all: Yamaha XT-660Z Tenere 2008 - 2016 Yamaha XT-660ZA ABS Tenere 2011 - 2016

Made from high quality plastic, this high screen offers better protection from wind and rain than the original windscreen. Turbulence around the helmet is minimised which results in a more enjoyable riding experience, even on longer distance rides. Street legel, TUV approved! The fly screen is about 8cm higher than the stock screen. Width is about the same like the oem screen. · Higher touring screen (+8cm) · Avaiable in different tints · Simply exchange for the stock screen · Stock bolts can be used · Round edge profile · Street legal The screen was recommended in the big 'Motorradfahrer' magazin accessories test in April/2010!  

S3 RALLY and ADVENTURE aluminium footpegs,height adjustable, for the Yamaha Tenere 700   Huge standing area, minimalist design and lightweight aluminium footpegs made from high grade aircraft aluminium 7075. Surface anodised for highest durability and top design. Exchangeable "teeth" for best grip, even when wet or in muddy conditions. Size is bigger than oem, so better ergonomics and feel especially when riding in standing position.   Adjustable in 3 positions:   2.5mm - High / Centered / 2.5mm - Low   Facts:   Rally / Adventure pegs with huge standing area Minimalist and lightweight Size of the peg for the foot: 115 x 65 mm Overall length incl. hinge: 140 mm Height can be individually adjusted Made of aluminium 7075 Ergal Wider width, for greater stability above the bike The "U" shaped design avoids blockages in ruts The special design keeps the stirrups clean from mud Stainless steel "teeth" exchangeable     Fits all:   Yamaha XT-660Z Tenere 2008-2016 Yamaha XT-660ZA ABS Tenere 2011-2016

Precisely CNC machined handlebar clamp set for 22 mm (7/8") standard or 28 mm (1-1/8") handlebars like e.g. Magura, Answer or ProTaperfor the Yamaha XT-660Z and XT-660ZA (ABS) model range. Special set made with the needed height and all mounting parts for the XT660Z and XT660ZA . We manufacture this clamps on modern cnc machines here in our own production. Made in Germany!   The fully cnc machined clamping sets have a height of 20mm (bottom of clamp to lower side of handlebar). By using the avaiable distance bushings almost all needed heights are possible. The shown complete height is measured between the lower side of the handlebar and the upper side of the triple clamps.   The dropdown menue shows the height you will get compared to the oem handlebar height. This is measured between the lower end of the handlebar and the upper side of the triple clamps. So +20 mm means that the handlebar position will be +20 mm compared to the oem height. If you want to have oem height, choose +0 mm. If the listed height is not enough for your needs, you can add extra height with the spacers shown in the 'accessories' section. New bolts needed, see accessries. Mounting heights up to +30mm compared to OEM height is quite easy, all height more than +30mm might require longer cable and wires. See accessories.   M10 bolts used for mounting to the triple clamp. Delivered bolts are 40 mm longer than height of ordered clamps. If you have choosen a height of e.g. 50 mm, the included bolts are 90 mm long. If you need different bolt length, see accessories tab. For individually needed distance bushings see accessories.   Details: Material: aircraft aluminium 7075 T6 Color: silver or black anodised Price per pair Delivery including fiiting M10 bolts Made by OTR with 10 years warranty!   Fits all:   Yamaha XT-660Z Tenere 2010-2016 Yamaha XT-6660ZA ABS Tenere 2011-2016

Off-centered handlebar mounting set for 22 mm handlebars   The excentric manufacturing offers a +/-5 mm for- or backward orientated handlebar mounting positon compared to a centered position. The fully cnc machined clamping sets have a height of  30 mm (upper side of triple clamp to lower side of handlebar). By using the avaiable distance bushings almost all needed heights are possible. So if you need a total height of e.g. 50 mm, choose the handlebar clamp (30 mm height) and add a 20 mm distance bushing.   Made of high grade aircraft aluminium, black or silver anodised. For needed distance bushings see accessories. Shown bushings not included!   Supplied M10 bolts have a free length  of 40 mm. If you have e.g. a 40 mm high triple clamp, these bolts will fit. If you need longer/shorter bolts, please order separately (see accessories).   Fits e.g. Yamaha XT-660R/X, XT-660Z Tenere, TT-600 (S/E/R/RE), XT-600, XT-550, XTz-660 any many more bikes with a bolt-on clamp set and 22 mm handlebar Please measure the needed height on your bike.   Tested, maximum possible heights with stock cables and wires:   Yamaha Tenere 700            -   90 mm Yamaha XT-660Z Tenere   -   70 mm Yamaha XTz-660                 -   70 mm Yamaha XT-660R/X            -   50 mm Yamaha TT-600                   -   50 mm Yamaha XT-600                   -   50 mm Yamaha XT-550                   -   50 mm   Color: silver or black anodised Price per pair Made in Germany by OTR with 10 years warranty! Shown spacers not included in delivery

Off-centered handlebar mounting set for 28 mm (1/1/8") handlebars like e.g. Magura, Renthal Pro Taper.   The excentric manufacturing offers a +/-5 mm for- or backward orientated handlebar mounting positon compared to a centered position. The fully cnc machined clamping sets have a height of  30 mm (upper side of triple clamp to lower side of handlebar). By using the avaiable distance bushings almost all needed heights are possible. So if you need a total height of e.g. 50mm, choose the handlebar clamp (30 mm height) and add a 20 mm distance bushing.   Made of high grade aircraft aluminium, black or silver anodised. For needed distance bushings see accessories. Shown bushings not included!   Supplied M10 bolts have a free length  of 40 mm. If you have e.g. a 40 mm high triple clamp, these bolts will fit. If you need longer/shorter bolts, please order separately (see accessories).   Fits e.g. Yamaha Tenere 700 or also, with new 28.6mm handlebar, Yamaha XT-660R/X, XT-660Z Tenere, TT-600 (S/E/R/RE), XT-600, XT-550, XTz-660 any many more bikes with a bolt-on clamp set. Please measure the needed height on your bike.   Tested, maximum possible heights with stock cables and wires:   Yamaha Tenere 700            -   90 mm Yamaha XT-660Z Tenere   -   70 mm Yamaha XTz-660                 -   70 mm Yamaha XT-660R/X            -   50 mm Yamaha TT-600                   -   50 mm Yamaha XT-600                   -   50 mm Yamaha XT-550                   -   50 mm   Color: silver or black anodised Price per pair Made in Germany by OTR with 10 years warranty! Shown spacers not included in delivery

Precisely CNC machined and strong RAID handlebar clamp set for Yamaha XT-660Z Tenere   The upper handlebar clamping plate provides a high torsional stiffness of the complete set. The handlebar height can be individually varied with additional spacers. We manufacture this clamps on modern cnc machines here in our own production. The avaiable versions are the height compared to the stock handlebar clamp height. Measured in mm between the lower end of the handlebar and the top of the triple clamps. The specified height refers to the lower edge of the handlebar to the upper edge of the triple clamp. +0 mm means the same height as standard, +20 mm means the handlebar position is 20 mm higher than standard. If the listed height is not enough for your needs, you can add additonal spacers shown in the 'accessories' section. New bolts are needed as well. OEM brake lines and clutch cables work up to a height 30mm more than stock.   Details: made from aircraft aluminium 7075 T6 high torsional stiffness handlebar position can be changed +/- 5 mm hight can be adjusted individually color: silver or black anodised additional spacer to lower or rise avaiable. See accessories Made in Germany by OTR 10 years warranty sold as a set   Fits all: Yamaha XT-660Z Tenere 2008-2016 Yamaha XT-660ZA ABS Tenere 2011-2016

Magura Hydraulic clutch for the Yamaha XT-660Z Tenere models. Constant pressure point, automatic adjustment, no need for maintenance, extremely good to batch, less operation power required, less weight. With an adjustable lever width, the HYMEC offers high ergonomics and the "fold-away" function prevents breakage when the motorbike falls over. Available in the standard length and an 8cm longer hose version for use with high handlebars or higher handlebar risers. MAGURA HYMEC - an easy-to-fit alternative to the mechanical clutch. With this system, the clutch lever and cable are replaced by a lightweight hydraulic system to improve clutch control. Hymec guarantees lower operating pressure, a constant pressure point, eliminates the hassle of cable adjustments and the very light clutch actuation ensures a perfect start every time. Hymec significantly improves driving performance - allowing the rider to feel the point at which the clutch is depressed and released. This product has been developed over many years and tested under the toughest imaginable off-road motorsport conditions. The world champions who have used it agree on its advantages, but the novice driver also benefits from it, for example when stopping at traffic lights. Hose available in a standard length or in a +8cm version to be used with high handlebars or risers. Facts: · Permanent play compensation, in other words the pressure point and the function of the clutch remain identical cold or hot. · Even wear characteristics and nearly maintenance-free. · Reduction of actuation forces by up to 25%. · Easy to install and route tubing. · Optimum lever kinematics and therefore improved metering ability. HYMEC improves vehicle performance considerably. The smooth-running hydraulics just makes it fun. · Magura HYMEC - a brilliant system for hydraulic actuation of a mechanical clutch. · Non-break forged lever with grip width adjustment and naturally with carbon tubing. · Filled with biodegradable mineral oil · Carbonium braided clutch hose · 25 % less hand power required due to the lack of friction within the clutch line. · Adjustable clutch lever · Minimal installing effort required. · No changes at the vehicle. · Safety switch remains. · With mirror mount · Delivered with newest clutch master cylinder version How does the hydraulic system work? The functional principle of the hydraulic system has been millionfold proved. It is based on the fact, that liquids cannot be compressed. On one side of line, the piston puts pressure on the liquid. The signal is transmitted to the piston on the other side of the line.  The size of the pistons defines the transmission ratio. If the face of the giver had half the size than that of the taker, the power of the taker would be double the giver's. The distance covered at the taker gets shorter due to the transmission. Compared to the serial clutch, the Hymec is much better in terms of effort and dosing ability. If you ever tried the Hymec, you would never give it back. The assembled hydraulic clutch just has to exchanged for the stock clutch. No modifications on the bike necessary! Fits all: · Yamaha XT-660 Z Tenere · Yamaha XT-660ZA ABS Tenere

The tapered X-Line handlebars from MAGURA: light, stable and easy on the joints. They also come with an even longer service life and are TÜV-tested. As a result of our patented manufacturing process the X-line handlebars offer a convincing strength to weight relationship. Ergonomically formed for increased comfort, proven in the Dakar Rally in the hands of the HRC team riders. High strength aluminium alloy with a ball blasted finish offers maximum stiffness and a long lifecycle. Although these handle bars do not have a cross-bar they are much stronger than usual handle bars. The conical aluminium handle bars are lightweight, stable, and gentle to the joints. With an even higher durability thanks to a shot peened finish. Because of the changed geometry a significantly relaxed driving is possible compared to the original. The bulged alloy handlebars from MAGURA are light, stable, reduced rider fatigue! Ball burnished finish for increased lifetime durability. All universal MAGURA handlebars are, of course, TÜV-approved and come with a certificate / ABE. If a registration is required, please check before purchase whether the desired vehicle is listed in the ABE. Otherwise, there is the possibility of registration by expert opinion. Details: · Magura X-Line - double butted handlebar · the original armatures and controls can still be used · available in various geometries · easy mounting within minutes · ball burnished finish · To be used with 28mm handlebar clamps · Street legal - comes with TÜV certificate for various models · Please check with measurements if this bars will fit your bike. If you have concerns about this, please ask.

Mirror extensions for mirrors mounted on the handlebar (M10 thread)   To ensure that your own shoulders aren't the only thing you see in the rear-view mirror, the extension elements provide a significantly improved field of vision by relocating the mirrors to the outside. Once adjusted and screwed on, the sturdy, well-designed extensions provide secure hold for the mirrors, even when riding off-road or at high speeds. Approval is available for tested motorcycle models.   Up to 4 cm higher, up to 4 cm lateral shift For improving the rear view Simple mounting onto mirror thread   Included in delivery 2 x Mirror extensions for mirrors mounted on the handlebar Mounting instructions Mounting material   Details Material: Aluminum Surface: anodized Color: black Total Weight: appr. 0,2 kg / appr. 0.3 lb   Fits e.g. for all: Yamaha Tenere 700, all models / years Yamaha Tenere 700 Rally, all models / years Yamaha Tenere 700 World Raid / World Rally, all models / years Yamaha Tenere 700 Extreme / Explore, all models / years Yamaha XT-660R Yamaha XT-660X Yamaha XT-660Z Tenere Yamaha XT-660ZA ABS Tenere Yamaha XT-1200Z Super Tenere Yamaha XT-1200ZE Super Tenere Yamaha MT-09 Yamaha MT-07

Pivot Pegz have been designed and built to last. They are a designed using high tech 3D computer modelling software and are a precision built product. They are formed by state of the art precision investment casting using high strength aerospace grade stainless steel before being CNC machined and double heat treated. Pivot Pegz are then electro-polished to a high grade finish before finally having the exterior hand polished to a mirror finish which highlights the embossed logo and really makes Pivot Pegz stand out in the crowd.   Internally a high quality German made BUSH is used and ample amounts of a superior quality saltwater proof grease is added to keep everything running smoothly. The unit also has O-ring seals at both ends of the pivot shaft to protect the internals and to keep the good stuff in and the bad stuff out. If and when maintenance is required it is a very easy task due to the simple and proven design. The strength and durability of Pivot Pegz has been proven many times and the product is considered by many as a must have performance part. PivotPegz are not only a breakthrough for cross- und enduro drivers, who claim insufficient sentitivity on the original footrests. They are also a gain for the ambitious tour driver on all routes. Via a spring joint Pivot Pegz adapt to the movement of the foot back and forth.   Advantages:   Better control: The power of the bike is spread onto the whole foot of the boot consistently via the same spot. Less exhausting: The permanent hits via the rim of the footrest are better compensated. Tilting of the boot over the rim of the footrest is eliminated. More pressure: When driving a bend the pressure on the bike is applied across the full width of the footrest and not only via the rim. Improved sensitivity: Thanks to the PivotPegz the footrest create a true connection between driver and bike. This way the driver is less exhausted and has a better sense for his bike. The lowering option of Pivot Pegz is available by interchanging the left and right Mount Assemblies. The end result is that you can lower your Pivot Pegz by about 8 mm. It's a simple task that takes around 10 minutes. Lowering requires no modification and can be reverted back to standard, quickly and easily.  It doesn't matter if you are riding off-road, on the street or touring - PivotPegz provide a much better handling and comfort!   Facts:   MK3 version: platform is 60mm wide and 85mm long Aerospace grade stainless steel - double heat treated Electro-polished Patented design O-ring sealed Spring loaded pivot action High grip tooth pattern Wide, open design Adjustable height Precision built High strength, high durability Optional springless pivoting action   Fits all:   Yamaha XT-660R 2004-2016 Yamaha XT-660X 2004-2016 Yamaha XT-660Z Tenere 2008-2016 Yamaha XT-660ZA Tenere ABS 2011-2016

Pivot Pegz have been designed and built to last. They are a designed using high tech 3D computer modelling software and are a precision built product. They are formed by state of the art precision investment casting using high strength aerospace grade stainless steel before being CNC machined and double heat treated. Pivot Pegz are then electro-polished to a high grade finish before finally having the exterior hand polished to a mirror finish which highlights the embossed logo and really makes Pivot Pegz stand out in the crowd.   Internally a high quality German made BUSH is used and ample amounts of a superior quality saltwater proof grease is added to keep everything running smoothly. The unit also has O-ring seals at both ends of the pivot shaft to protect the internals and to keep the good stuff in and the bad stuff out. If and when maintenance is required it is a very easy task due to the simple and proven design. The strength and durability of Pivot Pegz has been proven many times and the product is considered by many as a must have performance part. PivotPegz are not only a breakthrough for cross- und enduro drivers, who claim insufficient sentitivity on the original footrests. They are also a gain for the ambitious tour driver on all routes. Via a spring joint Pivot Pegz adapt to the movement of the foot back and forth.   Advantages:   Better control: The power of the bike is spread onto the whole foot of the boot consistently via the same spot. Less exhausting: The permanent hits via the rim of the footrest are better compensated. Tilting of the boot over the rim of the footrest is eliminated. More pressure: When driving a bend the pressure on the bike is applied across the full width of the footrest and not only via the rim. Improved sensitivity: Thanks to the PivotPegz the footrest create a true connection between driver and bike. This way the driver is less exhausted and has a better sense for his bike. The lowering option of Pivot Pegz is available by interchanging the left and right Mount Assemblies. The end result is that you can lower your Pivot Pegz by about 8 mm. It's a simple task that takes around 10 minutes. Lowering requires no modification and can be reverted back to standard, quickly and easily.  It doesn't matter if you are riding off-road, on the street or touring - PivotPegz provide a much better handling and comfort!   Facts:   MK4 version: platform is 60 mm wide and 100 mm long Aerospace grade stainless steel - double heat treated Electro-polished Patented design O-ring sealed Spring loaded pivot action High grip tooth pattern Wide, open design Adjustable height Precision built High strength, high durability Optional springless pivoting action   Fits all:   Yamaha XT-660R 2004-2016 Yamaha XT-660X 2004-2016 Yamaha XT-660Z Tenere 2008-2016 Yamaha XT-660ZA Tenere ABS 2011-2016

ProTaper handlebars - the original handlebar from USA. The ProTaper handlebar are second to none when it comes to strength and function. Perfect choice for Rally and Adventure riding use! The bar is an affordable way to get your hands on the most saught after handlebar design. Perfect for longer adventure or off-road rider - especially for driving standing position on long trips! We have tested a lot of ProTaper bars and found these two the best for Rally and Adventure/Trail riding. Due to the height an adjustment of the cables/wires might be necessary on your bike. Our choice when it come to Adventure rides!   Details:   ProTaper Handlebar version CONTOUR Made with aerospace aluminum and  thick wall tubing Adventure Evo is a bit stronger than the Contour version Very high strength due to the thick aluminium wall 28.6mm bar mount diameter - 22mm at the bar ends for use of stock switchs Bar inner diameter 13.8 mm Chemically applied scratch & peel resistant graphics Knurled clutch side for secure grip hold Includes high-density molded pad Colours: black, silver, platin or gold

ProTaper handlebars - the original handlebar from USA.   The ProTaper handlebar are second to none when it comes to strength and function. Perfect choice for Rally and Adventure riding use! The bar is an affordable way to get your hands on the most saught after handlebar design. Perfect for longer adventure or off-road rider - especially for driving standing position on long trips! We have tested a lot of ProTaper bars and found these two the best for Rally and Adventure/Trail riding. Due to the height an adjustment of the cables/wires might be necessary on your bike. Our choice when it come to Adventure rides!   Details:   ProTaper Handlebar version CONTOUR Made with aerospace aluminum and  thick wall tubing Adventure Evo is a bit stronger than the Contour version Very high strength due to the thick aluminium wall 28.6mm bar mount diameter - 22mm at the bar ends for use of stock switchs Bar inner diameter 13.8 mm Chemically applied scratch & peel resistant graphics Knurled clutch side for secure grip hold Includes high-density molded pad Colours: black, silver, platin or gold

ProTaper handlebar Adventure - the original handlebar from USA.   The ProTaper handlebar are second to none when it comes to strength and function. Perfect choice for Rally and Adventure riding use! The bar is an affordable way to get your hands on the most saught after handlebar design. Perfect for longer adventure or off-road rider - especially for driving standing position on long trips! We have tested a lot of ProTaper bars and found these two the best for Rally and Adventure/Trail riding. Due to the height an adjustment of the cables/wires might be necessary on your bike. Our choice when it come to Adventure rides!   Using the same manufacturing techniques and materials as ProTaper’s industry-changing 1⅛" motocross handlebar, the EVO Adventure is specifically designed to provide adventure/touring riders with the increased comfort and control they need. With over 8" of straight section in the control areas, mounting vital components is made easier than ever. With its premium 7000 series aluminum alloy construction and computer-profiled four millimeter-thick wall design, the EVO Adventure Handlebar is up to 25% lighter and 45% stronger than competing handlebars.   Please note the height when selecting the handlebar. Not on all bikes are compatible with their length of brake clutch lines.   Handlebars ADVENTURE EVO Very high strength due to the thick aluminium wall 28.6mm bar mount diameter - 22mm at the bar ends Chemically applied scratch & peel resistant graphics Knurled clutch side for secure grip hold Made from 4mm, proprietary, 7000 series aluminum alloy for superior tensile and yield strength Best balance between fatigue life, impact strength and impact absorbing flex High tech, stress relieved, shot peen and anodized finish for unmatched durability Independent lab tests show that the EVO handlebars outlast every other handlebar on the market in fatigue life Epoxy inner coating resists corrosion 8" higher of straight section Chemically applied cut lines and alignment grid are scratch and peel resistant End plugs help keep the elements out of the handlebar tubing and aid in longer grip life Weighs only 1.55 pounds (720 grams) Pad sold separately not street legal Colour: black

As some taller drivers of the XT660Z Tenere have little problems with some turbulences, we now offer a taller screen with an adjustable visor. So turbulences are reduced and comfort on the bike is much better - especially on longer trips. The adjustable spoiler alowys to find the exact angle for the best air flow. Made of brak resistant plastic - street legal (with TUV). Manufacturated from 3mm high resistant and durable acrylic. Rounded edge screen profile in 3mm. It's not necessary to mount a edge protection (otherwise not street legal in Germany).   Higher touring screen (+8cm) + additional height of visor Color: light tint Additional adjustable spoiler improves airflow and comfort Simply exchange for the stock screen Stock mounting screws can be used Round edge profile Street legal   Fits all:   Yamaha XT-660Z Tenere 2008-2016 Yamaha XT-660ZA ABS Tenere 2011-2016

Heatech Quickshifter Easy Yamaha XT-660 model range - go the Braaaapp... Braaapppp, Braappp way Next generation standalone quickshifter Easy to install. Easy to setup. Easy on your wallet. The perfect choice for anyone aiming for quicker lap times, better 1/4 mile runs or simply more fun on the road. Gear shifting is extremely fast (a few hundredths of a second) and comfortable. The sensation is that of a continuous transmission of power: you do not feel the push interruption typical of traditional gear changes. Simply and quick installation on the Yamaha XT660. Install ring sensor on the shift lever connection. Install wireing harness to the spark plug connectors. Install power supply - that's it! The unique ring-type QSS sensor works in in push directions and allows clutchless gear shift in a perfect way. With the iQSE the clutchless, full throttle shifts are not only quick but effortless too. Now you can shift like a pro! The quickshifter cuts the ignition at the moment you start moving the shift lever. The gearbox is unloaded, making it possible for you to switch one gear up without closing the throttle. By the time the spark comes back, you’re already in the next gear - no hassle, no glitch, no time loss. The iQSE is not only chosen by racers, but more and more street riders too due to the simple installation and affordable price. For street riders the benefit is improved control and comfort, and to put it simply, MORE FUN! It really makes all bikes more fun to ride, including classic and touring bikes too. · Measurements: 50 x 30 x 17 mm (1,9 "x 1,2" x 0,6 ") · Weight only: 43 g (1,51 Unzen)   Awesome tech · Change settings any time you wish through your phone, wirelessly, without hassle Simple installation · With our special ring sensor and the bike specific wiring harnesses, installation couldn’t get any simpler than this. Best choice · Packed with unbeatable features for an unbeatable price. Best price/value.   As easy as it can get The product was designed with the average rider in mind to make the installation and setup as simple as possible yet it has all the features needed for pro racers too. Supreme compatibility One sensor that works on all motorcycles, also with reverse (race) shift pattern. Plug ‘n Go harness kits are available for most bikes. Compatible with all our products too. Small yet powerful The iQSE module comes in a small package so you don’t have to sacrifice your under-seat storage space. Wireless connectivity The iQSE is the only quickshifter module on the market which utilizes wlan technology and iOS + Android app for setup and verification. Can even be disabled with a few taps to restore factory condition e.g. for servicing the bike. You’re in safe hands The module is weather and shock proof and comes with our 2-year warranty. We offer free and automatic software updates for the lifetime of this product. Even the module firmware is updated automatically via wlan (with our zero-risk technology) which makes the product future proof. Fits all: · Yamaha XT-660R 2004-2016 · Yamaha XT-660X 2004-2016 · Yamaha XT-660Z Tenere 2008-2016 · Yamaha XT-660ZA ABS Tenere 2011-2016

Renthal Fatbar 609 handlebars - the original handlebar from UK. The championship proven Renthal® Fatbar continues to set the industry standard in an unbraced mx handlebar. The oversized (1-1/8in | 28.6mm) clamping diameter uses computer aided profiling, tapering down to (7/8in | 22.2mm) to accept standard controls. Engineered from Renthal's exclusive 7010 T6 aluminum, specially formulated to reduce vibration and provide superior strength.   The Renthal MX Fatbar provides that signature flex character desired by many top atheltes around the globe and is fitted as OE equipment by various manufacturer. · handlebar including bar pad! · Made with aerospace aluminum and  thick wall tubing · Very high strength due to the thick aluminium wall · 28.6mm bar mount diameter - 22mm at the bar ends for use of stock switchs · Chemically applied scratch & peel resistant graphics · Knurled clutch side for secure grip hold · Includes high-density molded pad   Measurements: · Width: 802 mm · Height: 120 mm · Rise: 84 mm · Clamping area: 150 mm · Sweep: 56 mm · Control length: 190 mm · Inner diameter at bar end: 14 mm

S3 Aluminium Footpegs, height adjustable, for the Yamaha XT-660Z / ZA Tenere Minimalist design and lightweight aluminium footpegs made from high grade aircraft aluminium 7075. Surface anodised for highest durability and top design. Exchangeable "teeth" for best grip, even when wet or in muddy conditions. Size is bigger than oem, so better ergonomics and feel especially when riding in standing position.   Adjustable in 3 positions:   2.5mm - High / Centered / 2.5mm - Low   Facts:   Minimalist and lightweight Size of the peg for the foot: 93 x 65mm Overall length incl. hinge: 120 mm Height can be individually adjusted Made of aluminium 7075 Ergal Wider width, for greater stability above the bike The "U" shaped design avoids blockages in ruts The special design keeps the stirrups clean from mud Stainless steel "teeth" exchangeable     Fits all:   Yamaha XT-660Z Tenere 2008-2016 Yamaha XT-660ZA ABS Tenere 2011-2016

Distance bushing in various heights for our cnc machined handlebar clamps. The fully cnc machined bushing is avaible from 10-50mm height. By using this spacer in combination with our handlebar clamps almost all heights are possible. Made of high grade aircraft aluminium, black or silver anodised. Delivered without bolts. For bolts see accessories. To be used only with our cnc machined handlebar clamps or triple clamp sets. See accessories. Price per piece. For mounting two pieces needed.

The bar riser made of high-quality aluminum alloy moves the handlebars up by 28 mm and, depending on the setting, in 5 mm increments closer to the rider. The bar riser ensures noticeably more comfort when driving, because you can bring the handlebars closer to your own height for a more comfortable and upright sitting position. You have the choice between seven different positions, in 5 millimeter increments. The sturdy and weather-resistant bar riser fits on handlebars with a diameter of 28 mm.   Made from high-strength aluminum alloy, CNC-etched Corrosion protection thanks to anodized finish With engraved logo and SW-MOTECH lettering For a more relaxed sitting position Adjust the position of the handlebars to one of 6 positions, at 5 millimeter increments Height increase of 28 millimeters For handlebars with a diameter of 28 mm   Included in delivery   2 x Bar back variable for Ø28 Lenker 2 x Handlebar clamps Mounting instructions Mounting material   Details   Material: Aluminum Surface: anodized Color: black Total Weight: appr. 0,6 kg / appr. 1.3 lb   Note   The length of the Bowden cables and brake lines must be individually verified.

SW-MOTECH Bar back 22mm handlebars If you find it difficult to comfortably reach the handlebar, you should consider purchasing a bar back. Our durable aluminum bar backs relocate the handlebar 30 mm up and 21 mm back. That adjustment adds more comfort during longer trips. · Moves bar position up 30 mm and back 21 mm · Hole spacing: 37-46 mm · Material: aluminum, powder coated · Colour: black or silver Included: · Bar back for handlebars with Ø 22 mm · Mounting material · Mounting instructions · Bike-specific ABE (permission for public roads in Germany)