Clutch cable in OEM quality for the Yamaha XT-660 models. Replacement part for the worn stock cable or as a emergency spare part for your desert trip. Note: The upper rubber collar has to be taken from the stock part. Length like oem cable. Fits all: · Yamaha XT-660R 2004-2016 · Yamaha XT-660X 2004-2016 · Yamaha XT-660Z Tenere 2008-2016 · Yamaha XT-660ZA ABS TEnere 2011-2016

Extended Clutch cable in OEM quality for the Yamaha XT-660 models. Length is +4cm compared to stock length. Extended version for use with e.g. handlebar riser or higher handlebars. Also as peplacement part for the worn stock cable or as a emergency spare part for your desert trip. Note: The upper rubber collar has to be taken from the stock part. Fits all: · Yamaha XT-660R 2004-2016 · Yamaha XT-660X 2004-2016 · Yamaha XT-660Z Tenere 2008-2016 · Yamaha XT-660ZA ABS TEnere 2011-2016

Cush drive rubber Yamaha XT-660 Increased clearance in the rear hub of the XT-660 is not unchangeable. The cushion dampers, which are built in in the rear wheel hub, should periodically be checked and changed if necessary. The bike will run much smoother with new chusion dampers. Sold as a set with 4 pieces. Fits e.g. all: · Yamaha XT-660R · Yamaha XT-660X · Yamaha XT-660Z Tenere · Yamaha XT-660ZA (ABS) Tenere · Yamaha MT-03

Complete set with oil seals and dust caps. These should be replaced at least every 2 years, depending on the riding performance, to ensure a perfect response of the fork. Due to aging or dirt on the fork tubes tubes, fork oil seals can be damaged. The result is a fork oil leakage at the damaged sealing rings. Leaking fork oil is very dangerous and should be avoided in time. Leaking fork oil attacks plastic, metal and painted surfaces, reduces a safe braking process when in contact with brake parts and causes unsafe grip losses on tires. For quality reasons, we only offer high quality shaft seals and dust caps with 3-fold sealing lip. · better breakaway torque and up to 3x less friction than OE Simmerrings · Patented Max-Life manufacture, which increases the life span by 3-4 times · fork seals have 3 sealing lips · Dust caps are coated with a special grease to improve the response Our Tip: Use only for your bike recommended fork oil and mount the seals with a little grease on the sealing lip. Clean the fork tube with chrome polish before mounting new seals. If the fork tubes is damaged with pitting (uneven surface) replace it. An uneven surface may damage the seals quick. Clean fork tubes regularly and grease with Teflon spray. Fits for: · XT-660R   2004-2016 · XT-660X   2004-2016 · XT-660Z   2008-2014 · XT-660ZA 2011-2014 Does not fit for the XT-660Z / ZA 2015-2016 with lower height dust caps!

Fork gaiters made of high-quality rubber for secure sealing and protection of the fork oil seals and dust caps. Universal fit for many models. Perfect, long-lasting protection of the fork and its sealing rings. The special structure of the folds allows better compression. In addition, a reinforcement on the outside of the bellows prevents the occurrence of dents. The special construction of this boots with breater holes will not influence the compression of the fork.   Details:   Complete with fixing material Price per pair. Available in 4 colours Suitable for motorbikes with 42-45 mm standpipe diameter and 60 mm sliding tube diameter minimum length: 200 mm maximum length: 350 mm

Replacement for worn out or leaky stock Yamaha fork oil seals with 43mm diameter. High-quality NOK spare seal set with additional sealing lip (3-fold sealing). Essential as replacement when travelling or as a replacement part for worn stock seals. Sold as a pair. Fits e.g.: · Yamaha XT-660R 2004-2016 · Yamaha XT-660X 2004-2016 · Yamaha XT-660Z Tenere 2008-2016 · Yamaha XT-660ZA Tenere (ABS) 2011-2016 · Yamaha XT-1200Z Super Tenere 2010-2013 · Yamaha XT-1200Z Super Tenere 2014-2016 · Yamaha XT-1200Z Super Tenere 2017- · Yamaha XT-1200ZE Super Tenere 2014-2016 · Yamaha XT-1200ZE Super Tenere 2017-

Fork slide bearings Yamaha XT-660Z Tenere Replacement set for worn fork bushings (slide bearings). While repairing or maintenance a front fork you should not only change the oil, seals and dust caps, you also have to replace the bushings. Only this will give your fork the smooth travel you want. Worn bushings can cause a damage on the chrome surface on the fork tubes! Only new, true to size bushings will give youf fork the best response behaviour and the best guidance for the fork tubes. Replacement set of 4 fork bushing to overhaul your XT-660Z forks. We offer a high-quality  set of 4 bushings for both fork tubes.

Fork slide bearings Yamaha XT-660ZA ABS Tenere Replacement set for worn fork bushings (slide bearings). While repairing or maintenance a front fork you should not only change the oil, seals and dust caps, you also have to replace the bushings. Only this will give your fork the smooth travel you want. Worn bushings can cause a damage on the chrome surface on the fork tubes! Only new, true to size bushings will give youf fork the best response behaviour and the best guidance for the fork tubes. Replacement set of 4 fork bushing to overhaul your XT-660Z forks. We offer a high-quality  set of 4 bushings for both fork tubes.

Öhlins linear fork springs for Yamaha XT-660Z Tenere from 2008 - 2016   Replacing the fork springs is a cost-effective and efficient way to improve the front fork of the XT660Z Tenere. Together with the specially developed fork oil from Öhlins, the response and performance of the original fork can be significantly increased.   Depending on motorcycle type, rider weight and personal preferences and in combination with an indivuelle air chamber and oil viscosity improves the driving behavior noticeably. Best material selection and precise manufacturing guarantee a maximum of 1.5% deviation in the spring rate of Öhlins fork springs. The fork springs are made of high quality chrome silicon spring steel, are linear wound, slightly firmer than the original springs, but finer from the response. Lifetime warranty! Delivery with or without fork oil.   Tip: Order suitable fork oil at the same time. About 1.5 - 1.6 liters of Öhlins oil 01314 #10 (alternatively viscosity 20 according to SAE specification) are required.   Fits for all:   Yamaha XT-660Z Tenere 2008-2016

Complete front fork repair and overhaul set for XT-660Z Tenere and XT-660ZA ABS Tenere   While repairing or maintenance a front fork you should not only change the oil, seals and dust caps, you also have to replace the bushings. Only this will give your fork the smooth travel you want. Worn bushings can cause a damage on the chrome surface on the fork tubes! Only new, true to size bushings will give youf fork the best response behaviour and the best guidance for the fork tubes. his is a repair set for both fork tubes. All necessary parts are included. eeded fork oil to be ordered seperately.   Yamaha XT-660Z: Oil quantity per fork leg 650 ml - air chamber 145 mm (Yamaha specs)   Content: Slide metal, inner Slide metal, outer Oil seals Dust caps O-Rings Seal rings Safety clips   Fits all: Yamaha XT-660Z Tenere 2008-2016 Yamaha XT-660ZA ABS Tenere 20011-2016

OFF-THE-ROAD fork valve tuning emulatos for the Yamaha XT-660Z Tenere model range The OFF-THE-ROAD fork valves turn  the Yamaha XT660's conventional fork without adjustment into an adjustable fork with adjustable compression. Due to the conversion, the fork responds more sensitively and does not immerse as strongly when braking. This results in a more controlled feeling with improved road contact. CAD developed and made of extremely light 6061 T6 aluminium. Surface anodized. Through a sophisticated system of holes in the valve, the oil flow in the fork is changed so that road contact and feedback is much more direct. The driver gains safety and feeling for the road surface. Applications: On-road, off-road, racing and touring applications.   The fork valves emulators are ready adjusted for the Yamaha XT660 forks. A subsequent fine adjustment can be made by the amount of oil or other oil viscosity and directly on the valve.  How it works: The OTR fork valve is inserted exactly with an adapter between piston rod and fork spring. Additional oil flow holes must be drilled in the piston rod. You find detailed instructions coming with the kit. Fine tuning of the fork valve is possible with little effort after installation by adjusting oil level, oil vicosity or adjusting the valve itself.   Price per pair. Tip: a complete overhaul of the fork is recommended on this occasion.  Available for: · Yamaha XT-660Z Tenere 2008-2016 · Yamaha XT-660ZA Tenere (ABS) 2011-2016  

High quality Headset bearing kit made according to OEM Japan quality. Unfortunately the stock Yamaha headset bearings don't last for ever. Sometimes it's necessary to exchange the bearings after 2-3 years. Important: Use a good grease while mounting the bearings. Yamaha was a little lazy at this point. Set with upper and lower bearing including the gasket! High quality bearing set Made in Japan Contains: 1 x Upper bearing 1 x Lower Bearing 2 x Seal rings

High-quality, viscosity-matching fork oil is an important factor when replacing fork springs. Hyperpro fork oil has special low friction additives to help make your fork action smoother and more consistent over a wide range of operating temperatures. Oil is avaiable with SAE 2.5, 5, 7.5, 10 and 15 Content: 1 Liter

If you find your fork tube bend after a heavy downfall in the country or on the street, you can now get an unexpensive replacement here. The tubes exactly match the original as regards length, quality, and manufacturing. By using only the best material and a very careful manufacturing process we can guarantee a constant high qualitiy of the tubes. Price for one fork tube. Fits all: · Yamaha XT-660Z Tenere 2008-2016 · Yamaha XT-660ZA ABS  Tenere 2011 (56P)

Motul Factory Line fork oil is a syntectic fork oil for on- and off-road use. The synthetic fork oil of Motul represent a high standard in the fork oil technology. The products are designed for use in all chassis components and provide good performance characteristics. To obtain the optimum viscosity for vehicle and operating conditions this fork oils are mixable. Specific formulation that contains an anti-friction additive specially developed by MOTUL to create easier sliding and to avoid drag in the fork. Stable absorption trough extended range of temperature thanks to the synthetic base stocks. Seals protection: excellent lubricant / elastomer compatibility. Anti-wear, anti-corrosion, anti-foaming. RECOMMENDATIONS MOTUL fork oil can be mixed to obtain the required absorption effect. Use the exact quantity recommended by the fork manufacturer. Specially formulated for SHOWA, KAYABA, ÖHLINS, WP USD forks and standard motorbike forks · Good damping properties at all temperatures · Good air releasea · Wear protection for extended service life of the fork components · Protection against corrosion of internal components · Content: 1 liter tin

Motul fork oil is a technosynthese fork oil for on- and off-road use. The technosynthese fork oil of Motul represent a high standard in the fork oil technology. The products are designed for use in all chassis components and provide good performance characteristics. To obtain the optimum viscosity for vehicle and operating conditions this fork oils are mixable. Specific Technosynthese® formulation that contains an anti-friction additive specially developed by MOTUL to create easier sliding and to avoid drag in the fork. Stable absorption trough extended range of temperature thanks to the synthetic base stocks. Seals protection: excellent lubricant / elastomer compatibility. Anti-wear, anti-corrosion, anti-foaming. RECOMMENDATIONS MOTUL Fork Oil Expert can be mixed to obtain the required absorption effect. Use the exact quantity recommended by the fork manufacturer. · Good damping properties at all temperatures · Good air release · Wear protection for extended service life of the fork components · Protection against corrosion of internal components · Content: 1 liter tin

Öhlins has developed high-quality oils for its shock absorbers, forks, and cartridge kits. They include a range of fork oils which will increase the performance of original telescopic and upside down forks. The different viscosities available make it possible to select the most suitable oil.   What distinguishes Öhlins fork oil from conventional oils is that it reduces friction, stays cleaner, has a long service life, and is highly resistant to foaming (known as cavitation). Together with the front fork springs from Öhlins, a considerable improvement in the responsiveness and performance of an original fork can be achieved.   Available fork oil types are: R&T: Fork oil with a viscosity of 19.0 centistokes at 40° Celsius (similar SAE 5 W)    #5: Fork oil with a viscosity of 20.0 centistokes at 40° Celsius (similar SAE 5 W)   #10: Fork oil with a viscosity of 40.0 centistokes at 40° Celsius (similar SAE 20 W)   #20: Fork oil with a viscosity of 98.0 centistokes at 40° Celsius (similar SAE 40 W)

Ohlins shock spring 01099 To allow the perfect setup of the bike for the riders weight and the track we offer a wide range of different spring rates for our MX & Enduro shock absorbers. Spring recommendations can be found in the mounting instruction for the specific shock absorbers. Features: · To be used for shock absorber series STX 46 · Material: steel, powder coated (yellow) · Inner diameter: 57 mm · Length: 220 mm · different spring rates avaiable Fits: · various Ohlins STX46 shocks

High Grade Alumnium Rear Sprocket Nut   The original sprocket nuts does not look that good after a while. Also they might have corrosion, as the oem nuts are steel made. For all fans of beautiful, threaded aluminum components, we now have a great alternative to the standard equipment. Our CNC machined sprocket nuts are elaborately milled from high quality aluminum. Thus, there is no more corrosion and the nuts look even much fancier than the standard nuts. In addition, these are protected by a tough anodized coating we scratches and scratches.   Details:   Made of high grade aircraft aluminum 7075 T6 Colour: silver, black, blue, red, gold or titanium color Material: Aluminum 7075 T6 Price per piece. You need 6 pieces for a set   Fits e.g.:   Yamaha Tenere 700 2019 onwards Yamaha XT-660R 2004-2016 Yamaha XT-660X 2004-2016 Yamaha XT-660Z Tenere 2008-2016 Yamaha XT-660ZA ABS Tenere 2011-2016

Stainless Steel Rear Sprocket Nut   The ugly stock steel sprocket nuts does not really fit to the look of an perfectly equipped bike. Also the oem nuts may corrode after a while. For all fans of precisely cnc made machine milled parts we offer this very nice sprocket nuts. The nut is made of high grade stainless steel, titanium or anodised aircraft aluminium 7075 T6.   Details:   Made of high grade stainless steel Colour: silver Material: Stainless steel Price per piece. You need 6 pieces for a set   Fits e.g.:   Yamaha Tenere 700 2019 onwards Yamaha XT-660R 2004-2016 Yamaha XT-660X 2004-2016 Yamaha XT-660Z Tenere 2008-2016 Yamaha XT-660ZA ABS Tenere 2011-2016

Titanium 6AL4V (Grad 5) made sprocket nut   The ugly stock steel sprocket nuts does not really fit to the look of an top finished bike. For all fans of precisely cnc made machine milled parts we offer this very nice sprocket nuts. The nut is made of high grade stainless steel, titanium or anodised aircraft aluminium 7075 T6.   Details:   Made of high grade titanium 6AL4V (Grad 5) Colour: titanium Price per piece. You need 6 pieces for a set   Fits e.g.:   Yamaha Tenere 700 2019 onwards Yamaha XT-660R 2004-2016 Yamaha XT-660X 2004-2016 Yamaha XT-660Z Tenere 2008-2016 Yamaha XT-660ZA ABS Tenere 2011-2016

Snap rings 43 mm  forks   Fits e.g. for all Yamaha Tenere 700, Yamaha XT-660R/X, Yamaha XT-660Z Tenere, Yamaha XT-1200Z Super Tenere

Suspension link arm (pivot) bearing repair kit including bearing pins for Yamaha XT-660Z Tenere. Comes with all needed parts to exchange the complete link arm bearings and seals.   The set contains the bearings, shafts and seals for the swing arm linkage and the bearings shafts and seals for the bottom of swingarm.   Include in delivery: 6 x high quality needle roller bearings 6 x oil seals (NBR quality) 3 x grounded and hardened shafts   Fits all: Yamaha XT-660Z Tenere 2008-2016 Yamaha XT-660ZA ABS Tenere 2011-2016   Note: Lower shock bearing not included. See accessories.

Complete suspension link arm (pivot) bearing repair kit for Yamaha XT-660Z Tenere. Comes with all needed parts to exchange the complete link arm bearings and seals. Contains 4 bearings and 4 seals for the swing arm linkage and 2 bearing and 2 seals for the bottom of swingarm. Lower rear shock linkage bearing / seal kit not included. See accessories. The set contains: · 6 x high quality needle roller bearings · 6 x oil seals (NBR quality) Fits all: · Yamaha XT-660Z Tenere 2008-2016 · Yamaha XT-660ZA ABS Tenere 2011-2016